SystemOmega

Táto stránka je iba na čítanie. Môžete si prehliadnuť zdrojový kód, ale nemôžete ho meniť. Opýtajte sa správcu, ak si myslíte, že niečo nie je v poriadku.
====== MCU ======
Zoznam súčiastok a modulov, vývojárskych prostriedkov a pomôcok

===== Projekty =====
==== Freezer - hromadný odpaľovač na fotoaparáty ====
[[.projects:3gr|3GR]]

==== Camera Motion Capture ====
[[.projects:camcap|Camera Motion Capture]]


===== Procesory =====
  * [[.arduino:stm32|STM32 ARM Cortex-M3 development board]] {{.arduino:stm32-front.jpg?direct&100|}}
  * [[.arduino:stm32l152|STM32 Nucleo ARM Cortex-M3 development board]] {{.arduino:stm32l152-front.jpg?direct&100|}}
  * [[.arduino:stm32f401|STM32 Nucleo ARM Cortex-M4 development board]] {{.arduino:stm32f401-front.jpg?direct&100|}}
  * [[.arduino:leaf_maple_mini|STM32 Leaf Maple Mini Cortex-M3 development board]] {{.arduino:stm32f103rcbt6-arm-cortex-m3-leaflabs-leaf-maple-mini-module-for-arduino-stm32.jpg?100|}}

===== Moduly =====
  * [[.arduino:esp8266|ESP8266 WiFi Modul]] 
  * [[.arduino:led_dot8x8|ICStation Led Matrix 8*8]]{{.arduino:led_dot8x8.jpg?direct&100|}}
  * [[.arduino:hy-srf05|HY-SRF05 ultrazvukový detektor]]{{.arduino:hy-sfr05-pinout.jpg?direct&100|}} 
  * [[.modules:er-sps06050s|MPU-6050 6-axis gyro]] Triple Axis Accelerometer & Gyro Breakout MPU-6050 (ER-SPS06050S)
  * [[.modules:er-sm9250mpu|MPU-9250 9-axis gyro]] IMU 9DOF MPU-9250 (ER-SM9250MPU) 9-axis MotionTracking device
  * [[.modules:adafruit-2021|Adafruit 2021 9-axis gyro]] Adafruit 9-DOF Accel/Mag/Gyro+Temp Breakout Board - LSM9DS0
  * [[.modules:adafruit-1604|Adafruit 1604 10-axis gyro]] Adafruit 10-DOF IMU Breakout - L3GD20 + LSM303 + BMP180
  * [[.modules:sen-13339|SparkFan SEN-13339 6-axis gyro]] 6 Degrees of Freedom Breakout LSM6DS3 (SparkFun SEN-13339)
  * [[.modules:sen-12636|SparkFan SEN-12636 9-axis gyro]] LSM9DS0 IMU Breakout - 9DoF (Sparkfun SEN-12636)
  * [[.modules:er-smO8810dof|Flight control 10-axis gyro]] IMU 10DOF MPU6050+HMC5883L+BMP085 (ER-SMO8810DOF) flight control sensor module
===== Súčiastky =====
  * [[.arduino:ne555|NE555 Pulse Module LM358]] {{.arduino:ne555-map.jpg?direct&100|}}
  * [[.suciastky:ua741cn|UA741CN OpAmp]] {{ .suciastky:opamp-ua741cn-pinout.gif?nolink&100 |}}

  * 5mW Red Light Module T Focus Stripe Lens Industrial Laser Head
    * Output: red laser straightly(650nm)
    * Size: approx. Φ12 x 35mm
    * Cable lenth: about 135mm
    * Working voltage: 3-5V
    * Current: 40mA (Max)
  * 5PCS Micro USB 5V 1A 18650 Lithium Battery Charger Board With Protection Module
    * Charge module- Linear charging.
    * Current- 1A adjustable.
    * Charge precision- 1.5%.
    * Input voltage- 4.5V-5.5V.
    * Full charge voltage- 4.2V.
    * Led indicator- red is charging Green is full charged.
    * Input interface- micro USB.
    * Work temperature- -10℃ to +85℃.
    * Inversed polarity- NO.
    * Size- small to 25X19X10mm.
    * Ampere meter can only be connected to 5v input end of the module.
    * It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
    * The connection wire should not be too thick.
    * Make sure the connect point is good.
    * If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip.
    * NO Reveral polarity.
SystemOmega

Nástroje používateľa

Nástoje správy stránok

Nástoje stránky
