Tu môžete vidieť rozdiely medzi vybranou verziou a aktuálnou verziou danej stránky.
Both sides previous revision Previous revision Next revision | Previous revision | ||
mcu:start [2016/04/26 14:15] Stanislav Nízky |
mcu:start [2016/05/02 12:08] (aktuálne) Stanislav Nízky |
||
---|---|---|---|
Riadok 1: | Riadok 1: | ||
+ | ====== MCU ====== | ||
+ | Zoznam súčiastok a modulov, vývojárskych prostriedkov a pomôcok | ||
+ | |||
+ | ===== Projekty ===== | ||
+ | ==== Freezer - hromadný odpaľovač na fotoaparáty ==== | ||
+ | [[.projects:3gr|3GR]] | ||
+ | |||
+ | ==== Camera Motion Capture ==== | ||
+ | [[.projects:camcap|Camera Motion Capture]] | ||
+ | |||
+ | |||
+ | ===== Procesory ===== | ||
+ | * [[.arduino:stm32|STM32 ARM Cortex-M3 development board]] {{.arduino:stm32-front.jpg?direct&100|}} | ||
+ | * [[.arduino:stm32l152|STM32 Nucleo ARM Cortex-M3 development board]] {{.arduino:stm32l152-front.jpg?direct&100|}} | ||
+ | * [[.arduino:stm32f401|STM32 Nucleo ARM Cortex-M4 development board]] {{.arduino:stm32f401-front.jpg?direct&100|}} | ||
+ | * [[.arduino:leaf_maple_mini|STM32 Leaf Maple Mini Cortex-M3 development board]] {{.arduino:stm32f103rcbt6-arm-cortex-m3-leaflabs-leaf-maple-mini-module-for-arduino-stm32.jpg?100|}} | ||
+ | |||
+ | ===== Moduly ===== | ||
+ | * [[.arduino:esp8266|ESP8266 WiFi Modul]] | ||
+ | * [[.arduino:led_dot8x8|ICStation Led Matrix 8*8]]{{.arduino:led_dot8x8.jpg?direct&100|}} | ||
+ | * [[.arduino:hy-srf05|HY-SRF05 ultrazvukový detektor]]{{.arduino:hy-sfr05-pinout.jpg?direct&100|}} | ||
+ | * [[.modules:er-sps06050s|MPU-6050 6-axis gyro]] Triple Axis Accelerometer & Gyro Breakout MPU-6050 (ER-SPS06050S) | ||
+ | * [[.modules:er-sm9250mpu|MPU-9250 9-axis gyro]] IMU 9DOF MPU-9250 (ER-SM9250MPU) 9-axis MotionTracking device | ||
+ | * [[.modules:adafruit-2021|Adafruit 2021 9-axis gyro]] Adafruit 9-DOF Accel/Mag/Gyro+Temp Breakout Board - LSM9DS0 | ||
+ | * [[.modules:adafruit-1604|Adafruit 1604 10-axis gyro]] Adafruit 10-DOF IMU Breakout - L3GD20 + LSM303 + BMP180 | ||
+ | * [[.modules:sen-13339|SparkFan SEN-13339 6-axis gyro]] 6 Degrees of Freedom Breakout LSM6DS3 (SparkFun SEN-13339) | ||
+ | * [[.modules:sen-12636|SparkFan SEN-12636 9-axis gyro]] LSM9DS0 IMU Breakout - 9DoF (Sparkfun SEN-12636) | ||
+ | * [[.modules:er-smO8810dof|Flight control 10-axis gyro]] IMU 10DOF MPU6050+HMC5883L+BMP085 (ER-SMO8810DOF) flight control sensor module | ||
+ | ===== Súčiastky ===== | ||
+ | * [[.arduino:ne555|NE555 Pulse Module LM358]] {{.arduino:ne555-map.jpg?direct&100|}} | ||
+ | * [[.suciastky:ua741cn|UA741CN OpAmp]] {{ .suciastky:opamp-ua741cn-pinout.gif?nolink&100 |}} | ||
+ | |||
+ | * 5mW Red Light Module T Focus Stripe Lens Industrial Laser Head | ||
+ | * Output: red laser straightly(650nm) | ||
+ | * Size: approx. Φ12 x 35mm | ||
+ | * Cable lenth: about 135mm | ||
+ | * Working voltage: 3-5V | ||
+ | * Current: 40mA (Max) | ||
+ | * 5PCS Micro USB 5V 1A 18650 Lithium Battery Charger Board With Protection Module | ||
+ | * Charge module- Linear charging. | ||
+ | * Current- 1A adjustable. | ||
+ | * Charge precision- 1.5%. | ||
+ | * Input voltage- 4.5V-5.5V. | ||
+ | * Full charge voltage- 4.2V. | ||
+ | * Led indicator- red is charging Green is full charged. | ||
+ | * Input interface- micro USB. | ||
+ | * Work temperature- -10℃ to +85℃. | ||
+ | * Inversed polarity- NO. | ||
+ | * Size- small to 25X19X10mm. | ||
+ | * Ampere meter can only be connected to 5v input end of the module. | ||
+ | * It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. | ||
+ | * The connection wire should not be too thick. | ||
+ | * Make sure the connect point is good. | ||
+ | * If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-substract the charging current to avoid burn damage to chip. | ||
+ | * NO Reveral polarity. | ||